aFe is proud to announce the Release of a new Magnum Force Stage 2 Sealed Air Intake System for the 2011 Ford Super Duty V8-6.7L (td). This system is available with a Pro DRY S filter (P/N: 51-81872), Pro 5R filter (P/N: 54-81872), Pro GUARD 7 filter (P/N: 75-81872-0), or a Value Pack (75-81872-0V). The Value Pack includes a Pro GUARD 7 Filter, Pro DRY S Filter, Restore Kit and Pre-Filter.
To order click on image. For more information call
or email
Click aFe for more products.
Competition Clutch now offers a clutch and flywheel for VQ35HR/VQ37HR equipped cars. The clutch kit includes an upgraded 250mm performance pressure plate, your choice of performance disc, pilot bushing and an alignment tool.
The Competition Clutch stage 2 kit utilizes an organic brass plus full-face disc with our performance pressure plate and is good for up to 450WTQ while maintaining a soft pedal and smooth engagement.
The Competition Clutch stage 4 clutch kit utilizes a 6 puck ceramic disc with our performance pressure plate and is good for up to 550WTQ while maintaining a soft pedal and smooth engagement.
To order click on image. For more information call:
or email
Click Competition Clutch for more products.
KW Suspensions announces their stainless steel constructed coil-over for the 2010+ Chevrolet Camaro Convertible. Two Variants of the KW suspension line up will be available.
The KW Suspensions coilover for the Camaro Convertible enables the owner to lower their vehicle 0.9-1.8 on the front axle and 0.8-2.0 on the rear axle and retains enough travel to handle maximum load and dynamic loads during driving. Variant 1 with its preset dampening rates permits customized lowering of the suspension and creates an optimized balance of sportiness, comfort and safety. With the Variant 3 drivers are able to adapt the suspension to their driving style, by using the fully adjustable independent rebound and compression technology to achieve the maximum of performance, driving comfort and safety. All KW coilovers come with a lifetime warranty and pass stringent German TUV safety & quality testing standards. Each kit is TUV approved.
To order click on image. For more
information call:
or email
Click KW Suspension for more products.
The Mishimoto Subaru WRX Silicone 80mm Airbox Hose is made from a combination of high-grade silicone and heat-resistant embedded fibers for a high-quality replacement kit for your OEM rubber hose. Available in black, blue or red, Mishimoto silicone hoses retain OEM fitment while providing increased pressure tolerance for the ultimate upgrade in performance and style.
Mishimoto guarantees superior performance and quality with an unmatched lifetime warranty on all parts.
To order click on image. For more information call:
or email
Click Mishimoto for more products.
The all new DiabloSport inTune is a revolution in the tuning industry! The inTune is the most affordable touch screen tuning device on the market today. It delivers an amazing user experience with easy to understand menus, automatic USB updates, and tons of vehicle specific features at an incredibly affordable price.
Plug the inTune into your vehicle’s diagnostic port and it will automatically detect your year, make and model. The inTune will then provide you with a list of DiabloSport preloaded tunes including Performance, Economy and/or specialty cold air intake/custom tunes. The device offers users the ability to monitor stock sensors in a numerical readout format and even has the capability to log data while using a third party device such as sensor AEM or PLX (O2 sensors, EGT, etc..).
The inTune also functions as a diagnostic code reader/clearer. Staying up to date with inTune couldn’t be any easier- simple free updates via USB with our new Auto Updater technology mean there’s no software to install and no additional hardware required to get the latest version! Simply plug your inTune in to your PC and get the latest firmware download automatically to your device. Updates can include improved tunes, new features, better functionality and even new GUI enhancements.
The inTune is like no other flash tuning device on the market offering all of the functions users want at an incredible price and it can even fit in your pocket!
To order click on image. For more information call
or email
Click DiabloSport inTune for more products.
The Cosworth High Flow Subaru Fuel Rail Kit is specifically designed for “top feed” style fuel injectors and is configurable for various fuel line installation scenarios. Each fuel rail is machined from solid aluminum and features a natural hard anodized finish for lasting durability. Each kit includes dash 6 AN fittings that will allow you to install fuel lines of your choice. This kit is intended for race and high performance applications and is not intended as a direct replacement for the factory fuel lines and fuel rails. Can be used with the Cosworth TGV Delete Kit (PN 20015678).
Includes:
•2 Fuel Rails
•4 M8 x 1.25 x 45 Stainless Cap Head Bolts
•4 Dash 6 AN to 9/16-18 Adapter
•2 Dash 6 AN Port Plug
•4 Billet Fuel Rail Stand-off
•2 O-Ring 12.1 x 1.6
To order click on image. For more information call
or email
Click Cosworth for more products.
The Honda Driver Side mount is designed to produce crisper gear shifts by preventing the front end of the engine from pitching up or down, forward and back. Improves traction and reduces wheel hop. All Torque Solution engine mounts are are made of high grade billet aluminum material, urethane bushings, and steel pins. This is a direct replacement of the OEM Left side engine mount. This mount can be seen in some of the fastest Hondas on the street and at the track!
Features:
•Eliminates wheel hop / traction loss
•Improved 60fts / e.t’s
•Made out of lightweight 6061-T6 billet aluminum
•1000HP+ torture tested
•Black anodized / Torque Solution Laser engraved
•75A durometer bushings
•LifeTime Warranty
•Made in USA
To order click on image. For more information call:
or email
Click Torque Solutions for more products.
On a short list of definitive American muscle cars, arguably the top contender has to be the Corvette. Invented in 1951 by GM designer Harley Earl, who was inspired by the great European sports cars of the day. He was looking to create an American sports car that could compete and win at the race track. Two years later, the first Corvette strutted out of the Chevrolet factory in Flint, Michigan on June 30, 1953. That first year only 300 were made. Six generations and 1.5 million Corvettes later (and still counting), no other car has achieved 58 years of production, and clearly no other car has matched the romantic, near mystical appeal of Chevrolet’s powerful two-seat sports car. The name Corvette was borrowed from a line of small, fast, navy ships used in World War II.
Books have been written and businesses continue to thrive based on all that can be modified to further improve a Corvette’s performance, yet one of the easiest and most cost effective things you can do right now is simply replace the OEM air filter with AEM‘s new AE-07082 Dryflow air filter. The Dryflow filter is a direct replacement for the stock air filter.
AEM Dryflow air filters use an innovative high performance, oil-free, synthetic filtration material that provides the ultimate combination of airflow, filtration and performance. The material is a three-dimensional filtering medium which uses depth loading and structural screen wire to enhance airflow capabilities. The result is a true performance air filter designed to improve horsepower without the inconvenience of oil. AEM Dryflow filter media allows for easy cleaning using a synthetic filter cleaner and easy to follow cleaning instructions. All AEM replacement air filters for street vehicles come with a lifetime limited warranty. Your Chevy Corvette will wear out before this replacement air filter does!
To order click on image. For more information call:
or email
Click AEM for more products.
aFe is proud to announce the release of the first Scorcher Module for Popular Volkswagen TDI in both the Jetta (P/N: 77-46401) and Golf (P/N: 77-46402) models from 2009-2011. The aFe Power SCORCHER Module is designed to alter the fuel pressure signal at pre-determined points throughout the entire RPM range. The result is 10hp and 22lbs. x ft. torque gain and provides a broad power curve and reduced turbo lag. No cutting, drilling or splicing is required in this hassle-free 30 minute installation.
To order click on image. For more information call:
or email
Click aFe Power for more products.
Competition Clutch now offers a heavy duty pressure plate for the Evo 8/9/X. The kits include a 3,000lb pressure plate that has a near stock pedal feel, your choice of sprung or un-sprung performance disc, an alignment tool & throwout bearing.
To order click on image. For more information call:
or email
Click Competition Clutch for more products.