Advanced Clutch Technology (ACT) has released new high performance clutch kits and components for the 88-91 Toyota Camry 2.5L V6, 2004-2006 Toyota Camry 3.0L V6, 2004-2006 Toyota Camry 3.3L V6, and the 2002-2006 Toyota Camry LE and Solara 2.4L I-4.

ACT’s clutch kits for the applications listed above feature a Heavy Duty or Xtreme pressure plate that incorporates hardened diaphragm fingers for decreased wear. The Heavy Duty pressure plate provides a 29 percent increase in clamp force over the stock unit and the Xtreme pressure plate provides a 61 percent increase in clamp force over the stock unit. Both pressure plates meet SFI Specification 1.1.

The ACT Street Clutch Kits combine a Heavy Duty or Xtreme pressure plate and a Performance Organic Street Disc. The disc features special performance organic friction materials able to withstand increased heat and abuse, steel-backed linings for high-burst strength and modifications engineered for quicker shifting. ACT Street Clutch Kits provide a moderate and consistent pedal feel, smooth engagement and significantly improved durability. The torque capacity is increased up to 310 to 390 lbs./ft., depending on your pressure plate selection.

ACT Race Clutch Kits will hold between 400 to 500 lbs./ft. of torque depending on your pressure plate selection. They are combined with 6- or 4-pad spring-centered, or rigid hub cerametallic discs, which are very durable while allowing for quick shifting. The Xtreme discs are for high-power engines and recommended for track use only.

For more information call “1-800-997-TINT”

Some vehicles are built for performance with precision engineering and dedication to producing stand out results. The 2009 and 2010 Nissan 370Z Nizmo with 3.7 liter V6 engine is no exception. Even with a stock 303 horsepower at the wheels and 249 ft/lbs of torque, AEM engineers saw room for improvement on this high performance vehicle.

AEM has been a pioneer in the development of air intake systems for powerful import models, like the 370Z, since it was founded in 1987. Recently, AEM has developed a series of intakes referred to as ETI or Electronically Tuned Intake systems. This new twist on air intakes utilizes specially tuned circuitry that works with the vehicle’s electronics allowing large power gains. With traditional designs, maintaining a large tube diameter near the MAF sensor without downsizing or restricting airflow would, in many cases, cause issues with the vehicle’s electronics. With ETI technology the MAF sensor is not confused by the air flow change and continues to supply the right signals to the computer for proper fuel delivery. This allows air intake designs like AEM’s 41-1002P and 41-1002C to maintain the calibration intended by the factory while enjoying the benefits of a low restriction air intake system.

“The new Nismo Nissan 370Z ETI AEM intake system is a true cold air intake,” says AEM Co-founder John Concialdi. “It consists of two 2.75 inch diameter intake pipes that were developed for use on the standard edition Nissan 370Z. However, there were some minor differences between the normal 370Z and the Nismo Edition. A front mount oil cooler made us redesign the location of our windshield washer reservoir. With the increased reported horsepower rating from the manufacturer we dyno’d the Nismo 370Z and realized there was more potential for power. So we created a new ETI calibration specially designed for the Nismo 370Z that helped us pick up an estimated 19.7 hp and 14.6 ft-lbs of torque at 7100 RPM. The gains with the 41-1002 intake were much better than those seen on the standard Nissan 370Z.”

Concialdi also commented on another feature that makes this AEM cold air intake stand out, the fact that the 370Z NISMO front bumper does NOT need to be removed. This adds to the ease of installation and servicing for the 41-1002P and 41-1002C tuned intake and filter system.

The 41-1002P intake has tubes with a polished aluminum finish and the 41-1002C has tubes with a gun metal colored powder coated finish. Both come with AEM Dryflow air filters, which require no oil, are very durable and are easy to clean and reuse. Since the OEM windshield washer reservoir was in the way, both parts also come with a redesigned windshield washer reservoir that provides needed clearance. AEM’s new ETI system for the 2009 and 2010 Nissan 370Z Nismo is a must have upgrade for drivers looking to improve power and performance.

For more information call “1-800-997-TINT”

From the factory, excess crankcase vapors and residual oil are vented back into the intake manifold. The Moroso Air-Oil Separator is plumbed into the PCV system and captures this oil mist to reduce detonation and deposits on the intake track including the valves themselves. Its Billet Aluminum body compliments any engine compartment and can be polished, chromed or powder-coated for a custom look. It has a bottom drain with an elbow that makes draining the collected oil a mess-free proposition. The 85485 kit includes stainless steel mounting bracket, 1/2″ inlet and outlet fittings and 36″ of 3/8″ rubber hose for plumbing the Air-Oil Separator inline.

For more information call “1-800-997-TINT”

The Hyundai Genesis Coupe models with 300+ horsepower V6 engines may get the majority of the media coverage, however, it’s expected that half of all Genesis Coupe sales will be models equipped with the sporty 2.0L turbo engine.

The Genesis Coupe’s 2.0L turbo engine was developed out of a cooperation effort between Hyundai, Mitsubishi and Chrysler. The Genesis Coupe’s 2.0L turbo engine is essentially the same engine found in Mitsubishi’s legendary Lancer Evolution cars.

2010 Hyundai Genesis Coupe models are highly capable machines. However, K&N engineers are constantly in pursuit of more power. After looking under the hood, K&N engineers knew that, with their expertise, these cars were capable of more.

K&N intake 69-5302TTK replaces the intake tract with a textured black powder coated mandrel-bent aluminum intake tube and a K&N High-Flow Air Filter for high air-flow delivery. The 69-5302TTK incorporates a heat shield custom made for the Genesis, which retains use of the factory fresh air inlet, and helps to isolate the air filter from warm air under the hood. This intake system provides improved performance you can feel.

The result of this hard work and enthusiasm for performance is an estimated 7 extra horsepower at the wheels. K&N’s Research and Development Department tested a 2010 Hyundai Genesis Coupe with a 2.0L turbocharged L4 engine on our in-house dynamometer. Results showed horsepower increases throughout the RPM range with an estimated horsepower gain of 7.05 horsepower @ 4,000 RPM! Equally important is the extra 9.27 lb-ft of torque this car picked up at 4,000 RPM.

This air intake system uses a conical shaped, carbon fiber top, High-Flow Air Filter, part RP-4600. The filter captures harmful particles, provides high airflow, and long service life. This K&N air filter performs for up to 100,000 miles before service is required, depending on driving conditions.

For increased service intervals, K&N intake 69-5302TTK can be used with K&N Precharger filter wrap, part number 22-8036PK. Precharger filter wraps are made from a durable polyester material containing uniform micron openings which will stop small dirt particles; yet add little restriction to the airflow of the air filter.

69-5302TTK is a complete system which takes about 90 minutes or less to install with common hand tools. It uses stock mounting points, requires no drilling, and is covered by the K&N Million Mile Limited Warranty.

For more information call “1-800-997-TINT”

The BWR Race Mufflers were designed to out flow and out perform all other mufflers on the market while still retaining a nice quality sound pitch. They are constructed from 304 stainless steel and are masterfully hand tig welded to ensure the highest quality muffler available. Blackworks Race mufflers are available in 2.36″ inlet and 3″ inlet to suit nearly everyones needs, and both sizes have a 4″ polished outlet. BWR Mufflers come with a Lifetime Warranty.

For more information call “1-800-997-TINT”

Cusco is proud to release Safety21 and Chromoly roll cages with different attachment points for the 2008+ Honda Fit. These rollcages are made upon order and will be ready to ship 1 week from purchase.

For more information call “1-800-997-TINT”

Mishimoto has just unveiled an aluminum radiator designed for the 2007-2009 Nissan 350Z. The Mishimoto Nissan 350Z aluminum radiator is designed to be the ideal upgrade from your OEM radiator by providing up to 30% increased cooling capacity to protect daily drivers and performance cars alike from overheating. The Mishimoto Nissan 350Z radiator features a lightweight dual core made of 100% brazed aluminum and polished aluminum end tanks for improved performance and aesthetics. Due to a design that retains OEM fitment, installation will be effortless with no cutting or additional modifications required.

Mishimoto guarantees superior performance and quality with an unmatched lifetime warranty on all parts.

For more information call “1-800-997-TINT”

Advanced Clutch Technology (ACT) has released high performance Heavy Duty and Xtreme clutch kits for the 2009-2010 Toyota Corolla XRS, 2007-3/2008 Toyota Camry 2.4L I-4 and 3.5L V6, and 2009-2010 Toyota Matrix S and XRS 2.4L I-4.

ACT’s new clutch kits for the applications listed above feature a Heavy Duty or Xtreme pressure plate that incorporates hardened diaphragm fingers for decreased wear. The Heavy Duty pressure plate provides a 29 percent increase in clamp force over the stock unit and the Xtreme pressure plate provides a 61 percent increase in clamp force over the stock unit. Both pressure plates meet SFI Specfication 1.1.

The ACT Street Clutch Kits combine a Heavy Duty or Xtreme pressure plate and a Performance Organic Street Disc. The disc features special performance organic friction materials able to withstand increased heat and abuse, steel-backed linings for high-burst strength and modifications engineered for quicker shifting. ACT Street Clutch Kits provide a moderate and consistent pedal feel, smooth engagement and significantly improved durability. The torque capacity is increased up to 310 to 390 lbs./ft., depending on your pressure plate selection.

ACT Race Clutch Kits will hold 400 to 500 lbs./ft. of torque depending on your pressure plate selection. They are combined with 6- or 4-pad spring-centered, or rigid hub cerametallic discs, which are very durable while allowing for quick shifting. The Xtreme Discs are for high-power engines and recommended for track use only.

For more information call “1-800-997-TINT”

Unleash the hidden power of 18 h/p and 20 ft/lbs of torque from your G8!

Superior engineering and unparalleled technology is what goes into the all new PF7040! This race inspired cold air intake comes equipped with the patented MR step down process and Air Fusion. In addition to its patented tuning process, this system comes with a Web nano-fiber dry filter that stops contaminants on the surface while accelerating air-flow. Protect your engine from harsh and dirty environments with the web nano-fiber dry media as designed for the US Army Abrams M1 tanks. Trust the company that brought you: “The World’s First Tuned Air Intake System”

Key Features:
•MR Technology – tunes intake to factory air/fuel ratios
•Air Fusion – adjusts short/long term fuel trim levels
•Ultra-Flow, Web Nano-Fiber Dry Filter
•Machined And Tuned Sensor Adapter
•Calibrated Sensor Housing

For more information call “1-800-997-TINT”

The engineers at AEM saw potential in the GM-900 line up of models with the 4.8L and 5.3L engine configurations, and set they out to design a cold air intake system to unleash the true power of the GM powerplant. The air filter chosen for this project was a big 5-inch inlet oval filter which provides plenty of air flow and outstanding engine protection. After the overall design was finished, real world performance testing began. Dynamometer testing on three different vehicles showed an estimated increase of 10 horsepower and 10 ft-lbs of torque at 5100 RPM. This new intake fits a variety of 2009-2011 Chevrolet and GMC pick-ups and SUVs.

Key Features:
•Dyno Proven Power Gains
•Enhanced Engine Sound
•Heavy Duty 3/16″ Brackets
•Double Wound Hose Clamps
•Lifetime Limited Warranty
•Durable Roto-Molded Intake Tube and Custom Sealed Airbox
•DRYFLOW Air Filter •Dryflow Synthetic Filter Media – No Oil Required
•Thick 3D Media for increased airflow and higher capacity
•Incredibly easy to clean

For more information call “1-800-997-TINT”