Advanced Clutch Technology (ACT) has released Heavy Duty clutch kits for the 2007-2010 Jeep Wrangler 3.8L.

ACT’s new clutch kits for the 2007-2010 Jeep Wrangler include a Heavy Duty pressure plate, a choice of disc, release bearing, pilot bearing and alignment tool. The Heavy Duty pressure plate incorporates hardened diaphragm fingers for decreased wear and provides a 37 percent increase in clamp force over the stock unit.

The ACT Street clutch kits combine the Heavy Duty pressure plate with a performance organic street disc. The disc features premium organic friction materials able to withstand increased heat and abuse, steel-backed linings for high-burst strength and modifications engineered for quicker shifting. The ACT Street clutch kit provides a moderate and consistent pedal feel, smooth engagement and significantly improved durability. These kits have increased torque capacity up to 530 lbs./ft.

The ACT Race clutch kits combine the Heavy Duty pressure plate with a cerametallic Xtreme Race disc, which is available in 6-pad, spring-centered or rigid-hub design. These discs are very durable while allowing for quick shifting. The Xtreme Race discs are for high-powered engines and recommended for track use only. The ACT Race clutch kits will hold 680 lbs./ft. of torque.

To order click on image. For more information call:

“1-800-997-TINT”

or email

Everette@RPMSuperStore.Com

Click ACT for more products.

Mishimoto Acura Integra Type R radiator hoses are made from a combination of high-grade silicone and heat-resistant embedded fibers for a high-quality replacement kit for your OEM rubber hoses. Available in black, blue or red, Mishimoto silicone hoses retain OEM fitment while providing increased pressure tolerance for the ultimate upgrade in performance and style.

Mishimoto guarantees superior performance and quality with an unmatched lifetime warranty on all parts.

To order click on image. For more information call:

“1-800-997-TINT”

or email

Everette@RPMSuperStore.Com

Click Mishimoto for more products.

If you’re looking for the largest exhaust system without sacrificing the weight… look no further, ETS has one of largest diameter titanium exhaust system on the market for the MK4 93-97 Toyota Supra with a tubing diameter of 4.0″ (101mm). This exhaust system weighs in under 17lbs and features a full titanium design including titanium brackets. This is the most free flowing exhaust with minimal bends on the market.

Unlike some of the other “titanium” exhausts on the market that claim to be full titanium and only use a titanium muffler. The ETS Supra Titanium exhaust is constructed completely of titanium tubing, full titanium muffler and titanium brackets.

Features:

• Full Titanium w/ ETS Titanium Muffler
• 4.0″ (101mm) Titanium Tubing
• Full exhaust weight under 17lbs
• Fully Purge Welded
• Titanium V-band Flange
• Hand built in the USA
• ETS Lifetime Warranty

To order click on image. For more information call:

“1-800-997-TINT”

or email

Everette@RPMSuperStore.Com

Click ETS for more products.

Torque Solution aluminum radiator mount is a great dress up item for any engine bay. Get rid of the ugly and heavy stock steel mounts and replace them with our lightweight mounts. These weigh approximately 75% less than the stock mounts and do the same job.

Available without the insert or with brand new OEM insert.

• Made out of lightweight aluminum
• Stainless hardware included
• 75% lighter than stock
• Red Anodized
• Will not Rust
• Lifetime Warranty
• Made in USA

To order click on image. For more information call:

“1-800-997-TINT”

or email

Everette@RPMSuperStore.Com

Click Torque Solution for more products.

GTSPEC Roll Center/Bump Steer kit is a must on all lowered vehicles. Lowered vehicles that are not equipped with this kit are prone to poor alignment geometry. Currently, few kits on the market are marketed towards reduction in bump steer, re-alignment of camber/caster, increase of stability, reduction in under steer, improvement in steering feel and steering response. Lowering the center of gravity of a vehicle is the key to better handling. The greater angles that are increased by lowering the vehicle also puts stress on axles, knuckles, tie rods, ball joints, control arms, and bushing, to name a few. With the GTSPEC Roll Center/Bump Steer kit install, correct alignment geometry is regained and stress on the suspension components will be reduced. Our roll center kit will also produce a reduction in bump steer, re-alignment of camber/caster, increase stability, improvement in steering feel and response, and reduction in under steer. While other kits on the market are cast, the GTSPEC Roll Center/Bump kit is FORGED; known to last under harsh driving conditions.

To order click on image. For more information call:

“1-800-997-TINT”

or email

Everette@RPMSuperStore.Com

Click GTSPEC for more products.

The JE sport compact line now includes Asymmetrical Piston Forgings. The Asymmetrical design reduces weight in areas not necessary and adds strength to areas needed. All JE asymmetrical parts will now feature a pin offset and narrow pin design for lighter weight. In most cases there is a 10% reduction in weight.

Asymmetrical parts which will replace all of our 81mm-84.5mm shelf parts. This will Include Audi/VW’s, Acura/Honda’s, Toyota, Mazda, and Nissan’s currently in the line up.

Asymmetrical pistons ranges in 81-88mm bore.

To order click on image. For more information call:

“1-800-997-TINT”

or email

Everette@RPMSuperStore.Com

Click JE for more products.

Do you have an engine swap in your Honda project car and it rubs the underside of the hood? Eliminate this problem with our all-new Password:JDM Billet Aluminum Hood Risers Kit. Our hood riser kits are machined in house, in the USA, and are available in your choice of anodized Black, Gold, Purple, or Red finish. Each spacer is laser etched with the Password:JDM Logo. Our kit includes two hood riser, and four zinc plated hex bolts. Our hood riser kit will raise your hood 3/4″.

Optional upgrade kit:
Optional upgrade kit replaces the hex bolts with 4 password fender washers and 4 stainless flathead bolts.

To order click on image. For more information call:

“1-800-997-TINT”

or email

Everette@RPMSuperStore.Com

Click PASSWORD JDM for more products.